Hello, I hope you can help me. I set up the first installation (latest LU) with docker, however, after flashing the device, it could not reboot. Therefore, I did what instructed by the Thundercomm files, flash it in Windows with MULTIDL and everyhing seem to work fine, however the board isn't recognized yet by adb. (ubuntu 20.04) Searching this forums, I run the putty (debug) ang got the following log, apparently the frp partition is not found.
Thank you in advance,
DAC
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.3.2-00353-SM8250-1
S - IMAGE_VARIANT_STRING=Soc8250LAA
S - OEM_IMAGE_VERSION_STRING=b5765d9c8902
S - Boot Interface: UFS
S - Secure Boot: Off
S - Boot Config @ 0x00786070 = 0x00000001
S - JTAG ID @ 0x00786130 = 0x0015a0e1
S - OEM ID @ 0x00786138 = 0x00000000
S - Serial Number @ 0x00786134 = 0xf0f10ff5
S - OEM Config Row 0 @ 0x007841e0 = 0x0000000000000000
S - OEM Config Row 1 @ 0x007841e8 = 0x0000000000000000
S - Feature Config Row 0 @ 0x007841f8 = 0x0040200000000400
S - Feature Config Row 1 @ 0x00784200 = 0xc000000000000000
S - Core 0 Frequency, 1516 MHz
S - PBL Patch Ver: 5
S - PBL freq: 600 MHZ
D - 6210 - pbl_apps_init_timestamp
D - 37074 - bootable_media_detect_timestamp
D - 914 - bl_elf_metadata_loading_timestamp
D - 709 - bl_hash_seg_auth_timestamp
D - 6064 - bl_elf_loadable_segment_loading_timestamp
D - 5512 - bl_elf_segs_hash_verify_timestamp
D - 7022 - bl_sec_hash_seg_auth_timestamp
D - 820 - bl_sec_segs_hash_verify_timestamp
D - 35 - pbl_populate_shared_data_and_exit_timestamp
S - 64360 - PBL, End
B - 78446 - SBL1, Start
B - 193980 - SBL1 BUILD @ 16:20:20 on Sep 7 2021
B - 198158 - usb: usb_shared_hs_phy_init: hs phy cfg size , 0xc
D - 10644 - sbl1_hw_init
D - 31 - boot_flash_init
B - 293715 - UFS INQUIRY ID: SKhynix HN8T05BZGKX015 A002
B - 295758 - UFS Boot LUN: 1
D - 946 - Auth Metadata
D - 99491 - sbl1_xblconfig_init
D - 0 - boot_config_data_table_default_init
D - 183 - boot_config_data_table_init
B - 319640 - CDT Version:3,Platform ID:11,Major ID:1,Minor ID:0,Subtype:3
D - 17415 - sbl1_hw_platform_pre_ddr
D - 0 - devcfg init
B - 348828 - PM: PM 0=0x400008000000080:0x0
B - 348920 - PM: PM 1=0x400008000000040:0x0
B - 353281 - PM: PM 2=0x400008000000020:0x0
B - 357704 - PM: PM 5=0x400000000000000:0x0
B - 362065 - PM: POWER ON by KPDPWR,POWER OFF by RAW_XVDD_SHD
B - 474702 - PM: SET_VAL:Skip
B - 475251 - PM: PSI: b0x00_v0x53
B - 481320 - PM: Device Init # SPMI Transn: 5279
B - 490714 - PM: Driver Init # SPMI Transn: 558
B - 503646 - PM: battery Id: 7548
B - 503677 - PM: Debug Board detected
D - 166256 - pmic XBL init
D - 27541 - vsense_railway_cpr init
D - 201331 - sbl1_hw_pre_ddr_init
D - 0 - boot_dload_handle_forced_dload_timeout
D - 1433 - sbl1_load_ddr_training_data
D - 5093 - sbl1_ddr_set_params
B - 571326 - eCDT MRR - Data Starting Address: 0x09066D00
B - 573522 - DSF version = 156.8.18
B - 576968 - Manufacturer ID = 6, Device Type = 8
B - 580567 - Rank 0 size = 4096 MB, Rank 1 size = 4096 MB
D - 31202 - sbl1_ddr_init
D - 30 - boot_pre_ddi_entry
B - 593682 - do_ddr_training, Start
B - 624121 - DDR: Start of DDR Training Restore
B - 633546 - Frequency = 1805 MHz
B - 633546 - DDR: End of DDR Training Restore
D - 40168 - do_ddr_training, Delta
D - 47794 - sbl1_do_ddr_training
D - 0 - sbl1_hand_control_to_devprog_ddr
D - 1007 - boot_ddi_entry
B - 652883 - Pimem init cmd, entry
D - 10736 - Pimem init cmd, exit
D - 13908 - sbl1_post_ddr_init
D - 0 - sbl1_hw_init_secondary
B - 673348 - APDP Image Load, Start
D - 793 - Auth Metadata
D - 458 - Segments hash check
D - 9699 - APDP Image Loaded, Delta - (8204 Bytes)
D - 0 - boot_dload_dump_security_regions
B - 691526 - usb: UFS Serial - b50962c9
B - 695979 - usb: fedl, vbus_low
D - 8418 - boot_dload_check
D - 0 - boot_cache_set_memory_barrier
D - 0 - boot_smem_debug_init
D - 396 - boot_smem_init
D - 0 - boot_smem_alloc_for_minidump
B - 716780 - PM: SMEM Chgr Info Write Success
D - 4117 - boot_smem_store_pon_status
D - 31 - sbl1_hw_platform_smem
D - 61 - boot_ddr_share_data_to_aop
D - 549 - boot_clock_init_rpm
D - 0 - boot_vsense_copy_to_smem
D - 0 - boot_share_flash_data
D - 31 - boot_populate_ram_partition_table
D - 61 - boot_populate_ddr_details_shared_table
D - 0 - sbl1_tlmm_init
D - 0 - sbl1_efs_handle_cookies
D - 0 - boot_apt_test
B - 763506 - OEM_MISC Image Load, Start
D - 762 - Auth Metadata
D - 274 - Segments hash check
D - 9242 - OEM_MISC Image Loaded, Delta - (8192 Bytes)
B - 776164 - QTI_MISC Image Load, Start
D - 5337 - QTI_MISC Image Loaded, Delta - (0 Bytes)
B - 793122 - PM: PM Total Mem Allocated: 2940
D - 7716 - sbl1_pm_aop_pre_init_wrapper
B - 797697 - AOP Image Load, Start
D - 915 - Auth Metadata
D - 1952 - Segments hash check
D - 13359 - AOP Image Loaded, Delta - (198240 Bytes)
B - 814350 - QSEE Dev Config Image Load, Start
D - 793 - Auth Metadata
D - 580 - Segments hash check
D - 12505 - QSEE Dev Config Image Loaded, Delta - (43276 Bytes)
B - 835883 - QSEE Image Load, Start
D - 4331 - Auth Metadata
D - 21716 - Segments hash check
D - 68991 - QSEE Image Loaded, Delta - (3259708 Bytes)
D - 183 - sbl1_hw_play_vibr
B - 913719 - SEC Image Load, Start
D - 2958 - SEC Image Loaded, Delta - (0 Bytes)
B - 920154 - CPUCPFW Image Load, Start
D - 4728 - CPUCPFW Image Loaded, Delta - (0 Bytes)
B - 928725 - QHEE Image Load, Start
D - 854 - Auth Metadata
D - 2745 - Segments hash check
D - 12505 - QHEE Image Loaded, Delta - (448728 Bytes)
B - 944554 - OEM_HYP Image Load, Start
D - 5276 - OEM_HYP Image Loaded, Delta - (0 Bytes)
B - 953643 - STI Image Load, Start
D - 5094 - STI Image Loaded, Delta - (0 Bytes)
B - 962763 - APPSBL Image Load, Start
D - 854 - Auth Metadata
D - 12962 - Segments hash check
D - 23851 - APPSBL Image Loaded, Delta - (2510848 Bytes)
D - 0 - sbl1_appsbl_arch_determination
B - 995794 - SBL1, End
D - 921283 - SBL1, Delta
S - Flash Throughput, 236000 KB/s (6553608 Bytes, 27765 us)
S - DDR Frequency, 1555 MHz
UEFI Start [ 1210]
- 0x09FC01000 [ 1214] Sec.efi
ASLR : ON
DEP : ON (RTB)
Timer Delta : +2 mS
RAM Entry 0 : Base 0x080000000 Size 0x03B800000
RAM Entry 1 : Base 0x180000000 Size 0x100000000
RAM Entry 2 : Base 0x0C0000000 Size 0x0C0000000
Total RAM : 0x1FB800000
UEFI Ver : 5.0.210907.BOOT.XF.3.2-00353-SM8250-1
Build Info : 64b Sep 7 2021 16:20:56
Boot Device : UFS
PROD Mode : TRUE
Retail : TRUE
PM0: 30, PM1: 32, PM2: 31, PM3: 33, PM5: 36,
UFS INQUIRY ID: SKhynix HN8T05BZGKX015 A002
UFS Boot LUN: 1
HW Wdog Setting from PCD : Disabled
DisplayDxe: SW renderer mode enabled!
DisplayDxe: Resolution 640x480 (1 intf)
SPSSDxe:: SPSSDxe_PreLoadChecks SPSS loading in UEFI not supported for this chip ID = 455
UsbConfigLibOpenProtocols: PMI version (0x20)
UsbConfigInit: UsbConfigInit, not start on port: 0, mode 0
UsbConfigInit: UsbConfigInit, not start on port: 1, mode 0
APC1 IDDQ WC 0 , L2:0, CPU[0]:175, CPU[1]:175, CPU[2]:175, CPU[3]:175
APC1 Total 700
LoadSys TIME 0ms
tsens TIME 1ms
scm TIME 2ms
Load CPU 0 Slp: 0x89, Int: 0xFFFFFF9E
Load CPU 1 Slp: 0xE0, Int: 0xFFFFFF65
Load CPU 2 Slp: 0x84, Int: 0xF8
Load CPU 3 Slp: 0x107, Int: 0xFFFFFFB1
Load GPU 0 Slp: 0xB1, Int: 0xFE adc_min:0x18D adc_max:0x15F
Load NPU 0 Slp: 0x2F, Int: 0x18
LmhIsenseInit Pre CPU TIME 0ms
GLD IDDQ WC 0
LmhIsenseSubSysEntry Post SubSysEntryCb TIME 0ms
LmhIsenseSubSysEntry Post LmhIsenseSubSysInit TIME 0ms
LmhIsenseInitSubSys Post SubSysEntry TIME 0ms
LmhIsenseInitSubSys Post SubSysTrim TIME 0ms
LmhIsenseInitSubSys Post SubSysExit TIME 0ms
LmhIsenseInit Post CPU TIME 0ms
GPU IDDQ 25
LmhIsenseSubSysEntry Post SubSysEntryCb TIME 0ms
LmhIsenseSubSysEntry Post LmhIsenseSubSysInit TIME 0ms
LmhIsenseInitSubSys Post SubSysEntry TIME 0ms
LmhIsenseInitSubSys Post SubSysTrim TIME 0ms
LmhIsenseInitSubSys Post SubSysExit TIME 1ms
LmhIsenseInit Post GPU TIME 2ms
Entering in func1 of NPU TIME 2ms
NPU IDDQ 29
LmhIsenseSubSysEntry Post SubSysEntryCb TIME 0ms
LmhIsenseSubSysEntry Post LmhIsenseSubSysInit TIME 0ms
LmhIsenseInitSubSys Post SubSysEntry TIME 0ms
LmhIsenseInitSubSys Post SubSysTrim TIME 0ms
LmhIsenseInitSubSys Post SubSysExit TIME 0ms
LmhIsenseInit Post NPU TIME 2ms
isense TIME 5ms
ISENSE TOTAL TIME 5ms
Disp init wait [ 1681]
-----------------------------
Platform Init [ 1699] BDS
UEFI Ver : 5.0.210907.BOOT.XF.3.2-00353-SM8250-1
Platform : QRD
Chip Name : QRB5165
Chip Ver : 2.1
Chip Serial Number : 0xF0F10FF5
Silver cluster Core 0 Freq: 1516 MHz
-----------------------------
UEFI Total : 518 ms
POST Time [ 1728] OS Loader
Loader Build Info: Sep 14 2021 09:03:45
VB: Non-secure device: Security State: (0xF7F)
VB: RWDeviceState: Succeed using devinfo!
Error Reading from misc partition: No Media
KeyPress:258, BootReason:0
Fastboot=0, Recovery:0
GetVmData: making ScmCall to get HypInfo
GetVmData: No Vm data present! Status = (0x3)
VM Hyp calls not present
Active Slot _a is bootable, retry count 2
Booting from slot (_a)
Booting Into Mission Mode
Loading Image Start : 1749 ms
Loading Image Done : 1750 ms
Total Image Read size : 4096 Bytes
Loading Image Start : 1750 ms
Loading Image Done : 1774 ms
Total Image Read size : 23564288 Bytes
Loading Image Start : 1780 ms
Loading Image Done : 1806 ms
Total Image Read size : 25165824 Bytes
In Ubuntu ab ota platform, we don't use the system_a / _b slotsystem partition d oes not exist
GetSystemPath failed!
LoadImageAndAuth failed: Load Error
Launching fastboot
Fastboot Build Info: Sep 14 2021 09:03:42
usb_shared_hs_phy_init: hs phy cfg size: 12
usb_shared_ss_phy_init: ss phy cfg size: 143
ssusb_phy_init_success_lane_A: 0
Fastboot: Initializing...
VB: Non-secure device: Security State: (0xF7F)
Partition not found : frp
Error Reading FRP partition: Not Found
Fastboot: Processing commands
Failed to get the graphics output protocol.
Failed to get the graphics output protocol.
Failed to get width or height
Failed to get the graphics output protocol.
Failed to get the graphics output protocol.
Unable to show fastboot menu on screen: Out of Resources
hello customer,
Please run this command before starting adb command
export ANDROID_ADB_SERVER_PORT=5038
in mean time , going through the logs and will get back to you!
Thanks
Hello,
I tried that export command before and it didn't work, also in my case tcp is started on 5037 (although no device is detected). Therefore, I decided to built a new image now, using the second option of the LU release. It didn't boot again after the flashin process, but finally I had the green LED on (something that hadn't happened with the last version). I reboot manully and proceed to the do the following, in a new shell:
$ sudo adb kill-server
Here I added the export command but I don't really know if this work
export ANDROID_ADB_SERVER_PORT=5038
$ sudo adb start-server
adb devices
adb shell
Although, I finally have acces to the board I do not consider the issue is fixed as I had to change the image file.
Hello customer,
Reason is that the build is not compiled or might be error while flashing first time.Good to know that now device works fine
Hello mita.rathod
What are the differences between the first two options of LU releases then? I couldn't find this information anywhereelse.
Regards,
DAC
I am currently running into the same error. I however cannot connect using adb.
Is there a solution to this issue? I am using a current qrb5 image.
Format: Log Type - Time(microsec) - Message - Optional Info
I am currently running into the same error. I however cannot connect using adb.
Is there a solution to this issue? I am using a current qrb5 image.
Format: Log Type - Time(microsec) - Message - Optional Info